eigene Beiträge| neueste Beiträge| ungelesene Beiträge| unbeantwortete Beiträge| aktive Themen| Fördermitgliedschaft| Cockerpage

Templer Edition Cyborgs

Gott will es!
Bild

Benutzeravatar
Karsten001
Alteisenbewahrer
Wohnort: Casa Maroni
Beiträge: 75
Registriert: 07.02.2004 01:42

#76

19.04.2015 09:51

Habe es gefunden. Falls noch jemand die Infos benötigt habe ich diese hier gleich gepostet. Aber Achtung, diese Anleitung passt nicht zum Cyborg 06 stock board ( hat mehr Register ) und auch nicht zum stock 07er board ( wird über Farben programmiert ). Man findet die Beschreibung also in keinem der beiden MacDev Handbücher auf deren Homepage.

Programming Your Cyborg
To enter programming mode (only possible if tourney lock is off), you must hold the trigger while you turn the board on. The LED will show orange. You must keep the trigger held in until the LED changes to blue. This indicates that you are in programming mode.

To change a setting on the board, you must pull the trigger to indicate the register you wish to change. the board will then flash to indicate the current setting of that register. Wait for these flashes to finish, before entering the new register setting (via the trigger). If you do not wish to change the current setting, you may switch the board off to abort programming. Once you have entered a new setting, the LED will return to solid blue, and wait a new register. If you do not wish to change another register, you may turn the marker off.

Register Summary Table
1 - Debounce
2 - Dwell
3 - Rate of Fire
4 - Fire Mode
5 - Eye Sensitivity
6 - ABS Activation Time
7 - ABS Dwell Increase
8 - ABS On/Off
9 - Disable Eye Through Trigger
10 - Ramp Percentage
11 - Ramp Activation BPS

1. Debounce
Use this setting to avoid the marker recognising false trigger pulls.
The defaults is 5, with available settings from 1-30

2. Dwell
The dwell controls the amount of time your electronics use to fire a ball. The defaults is 8, if you set this too low, your marker will become inconsistent or not fire at all. If you set this too high, your marker will be slow and use more gas.

3. Rate of Fire
Use this setting to control the maximum speed your marker can achieve. The default setting is 1. A Setting of 1 will give the marker unlimited speed, whilst any other settings of 2-22 will give you a BPS cap equal to this setting.

4. Firemode
The firemode will allow you to set the marker for different rules or recreational use.
The modes are:
1. Semi
2. PSP
3. Millenium
4. NXL
5. 3 Shot Burst
6. 6 Shot Burst
7. Response
8. Custom Ramp
9. Breakout
10. Full Auto

5. Eye Sensitivity
This setting controls how quickly the eyes read the ball. A low seting will allow the greatest feeding speeds, however a higher setting will give more reliable reading. Default is 4, and it may be set from 1-30.

6. ABS time
This software oprion can alleviate problems with bolt stick by setting the time the software waits before applying anti bolt stick. The defaults is 10sec, however it can be set from 1-30sec.

7. ABS dwell increase
This is the maount of time added to the dwell to aleviate bolt stick. Default is 1, and it may be set from 1-30.

8. ABS on/off
Use this setting to enable or disable the ABS software. Do not use the ABS software unless oyu have bolt stick problem that cannot be fixed any other way. Defaults is 2 (off), otherwise it may be set to 1 (on).

9. Eye disable on/off
The ability to disable the eye system by holding the trigger in may be disabled here. Default is 1 (eye disable on), otherwise it may be set to 2 (eye disable off)

10. Ramp percentage
If you are using fire mode 8 (custom ramp) you can set the ramp percentage here. The default is 4 (100%), otherwise it may be set between 1-8 where 1(25%), 2(50%), 3(75%) ... 8(200%).

11. Ramp activation BPS
If you are using fire mode 8 (custom ramp) you can set the ramp activation here. The default is 5 (BPS), otherwise it may be set from 1-15 (BPS).

Link:
BBcode:
HTML:
Hide post links
Show post links
Benutzeravatar
SpecialKai
Podbitch
Podbitch
Beiträge: 184
Registriert: 20.03.2004 11:24

#77

31.08.2015 17:53

... :mnt:


das blutigste aller Schwerter ;) ist vor langer Zeit (25.09.2006, 17:38 Uhr ) nach Süden gepilgert.

Der derzeitige Besitzer ist und bleibt leider unbekannt.

Aber so sah es aus !

btw..
Schlauch hat seines auch noch, ich hatte es vor ca. 1 Jahr hier zum Schärfen


@Karsten ... es waren TAG Predator Boards drinne, kann das sein?!!! ;)


:mnt: ...
Dateianhänge
100_1477.JPG
cyborg.jpg

Link:
BBcode:
HTML:
Hide post links
Show post links

Zurück zu „2DIE4 Templer Braubach“

Wer ist online?

Mitglieder in diesem Forum: 0 Mitglieder und 3 Gäste