eigene Beiträge| neueste Beiträge| ungelesene Beiträge| unbeantwortete Beiträge| aktive Themen| Fördermitgliedschaft| Cockerpage

How to install Magna Drive

Das zu Hause deiner Paintballs
Benutzeravatar
Florian
Der alte Mann und das Hub
Wohnort: Frankfurt am Meer
ForumBadges: Bild
Beiträge: 25876
Registriert: 23.09.2003 12:25

How to install Magna Drive

#1

26.12.2007 13:46

Ok so here is the long overdue how to on how to install the Magna Clutch Kit.
First remove the screws on the shell.
Then remove the 2 screws on the upper raceway half
Then remove the anti-jam kit.
Then remove the drive cone, spring and spring cup.
Then remove the E-clip at the bottom of the raceway.
Bild

-Optional- If you do not have a rip drive right now do the fallowing.

Remove the 3 screws at the bottom of the raceway to expose the gears
Bild

Remove the belt and gear closest to the motor.
Bild

Remove the large gear.
Remove the E-clip from the short drive shaft
Remove the large gear from that drive shaft
Install the large gear on the new long rip drive shaft
Bild

Install the E-clip on the new drive shaft
Install the drive shaft back in to the raceway
Install the smaller gear and belt
Bild

Put the 3 screws back in to the gear box
Do not over tighten the screws

Install the magnets in the magnet holder how you wanted, I did the “brittle paint” set up.
Bild
Bild
(make sure your magnet holder is the other way I installed it wrong the 1st time but did not get a 2ed photo of it, sorry)
Bild
(easiest way to pull the magnets off.)
Install the magnet holder in the bottom of the raceway with the shim side down.

Install the clutch plate of your choice. I used the “N” style plate at the end but the photo has a triangle
Bild
Install the spring cup that has he star on the bottom of it.
Bild

Install the spring that you want there is the hard and soft spring I chose the hard spring.
Bild


While holding the lower drive cone install the drive cone cap so you don’t lose your prewinde.
Bild

Install the anti-jam kit
Install the upper raceway

Install the eyes if you have them, tape everything back in to place.

For Putting your raceway from a halo/Reloader B in to Magna Shells that you bought.
I am not responsible for you breaking your Halo/Reloader b, doing the fallowing will void your warranty.

Remove everything from your halo so you just have the raceway now. Take
the inner 2 wires on the motor side and cut them (white and red) add about 1” of wire using solder and heat shrink.
Bild

On the eye side if you have them cut and lengthen all 4 wires and solder and heat shrink again.
Bild

Test to make sure it all is working again.
Take the leads that the eyes and motor/battery wires plug in to and bend them up.
Bild
Bild


Next cut out a pattern that looks like this I’ll try and get a .PDF so you can print it put and use mine.
Bild
Bild

Once you do that it will create the raceway that the Magna uses.
Once you do that just put it all back together.
Bild
that is how I had to put the eye wires in so they didn't get messed pinched.
Bild

NOTE: There is a ramp in the magnas that you buy, right now Kee is not selling them on their own. But that paper template is the shape/size of one out of the Magna. With the template made in to a ramp made out of plastic like used in egg speed feeds allows it to work right.

Unless you can buy a ramp from your local shop. Once it is in the right spot there will be no gaps showing in the loader.

Link:
BBcode:
HTML:
Hide post links
Show post links
Benutzeravatar
Puschkin87
Rec-Baller
Rec-Baller
Wohnort: Düsseldorf
Beiträge: 321
Registriert: 08.11.2006 22:25

#2

26.12.2007 14:56

alltah wasn das mit den ganzen kabeln da..?
Das geht ja garnicht!

Link:
BBcode:
HTML:
Hide post links
Show post links
Benutzeravatar
Sh4d0w
X-Baller
X-Baller
Wohnort: Wien
Beiträge: 2935
Registriert: 10.12.2003 13:30

#3

26.12.2007 15:21

sind die verrückt ? ich hab doch keine lust raketentechniker spielen ... dann doch lieber meinen torque oder nen vlocity mit *

Link:
BBcode:
HTML:
Hide post links
Show post links
Benutzeravatar
Spawn_0815
Rookie
Rookie
Wohnort: Allgäu
Beiträge: 557
Registriert: 01.01.1970 01:00

#4

26.12.2007 16:49

Puschkin87 hat geschrieben:alltah wasn das mit den ganzen kabeln da..?
Das geht ja garnicht!
Die ganzen Kabel da sind die Augen vom Halo ...

Aber der Umbau is ja wohl das dümmste überhaupt ... sorry ... die Innereien eines Halos in nen Magna Drive zu bauen ... macht meiner Meinung nach keinen Sinn ...

Wenn dann schon eher den Magna Drive als "Upgrade" in die Drive Unit eines Halo B / Empire B1 oder B2 .... einbauen ... und da muss man ja (was ich so gesehen hab) nur den Drivecone usw. auswechseln um den "neuen" Magna Drive Effekt (der ja wie ne Art "Rutschkupplung" funktioniert) zu bekommen ... den Umbausatz gibts ja schon zu kaufen ... ist ne Mischung aus dem neuen Drive Cone System und nem Rip Drive Kit ...

Die Form des Magna Drive Loaders gefällt mir eh net ... aber das is n anderes Thema ...

Link:
BBcode:
HTML:
Hide post links
Show post links
Benutzeravatar
Laprada
Rookie
Rookie
Wohnort: Mörfelden - Walldorf
Beiträge: 697
Registriert: 06.02.2006 19:51

#5

26.12.2007 17:46

Ich sags euch, das ist ne Bombe...

Link:
BBcode:
HTML:
Hide post links
Show post links

Zurück zu „Hopper“

Wer ist online?

Mitglieder in diesem Forum: 0 Mitglieder und 4 Gäste