eigene Beiträge| neueste Beiträge| ungelesene Beiträge| unbeantwortete Beiträge| aktive Themen| Fördermitgliedschaft| Cockerpage

Ego Regulator

CS, LV, GTEK, ETEK, ETHA, EGO, GEO
Bild

Benutzeravatar
Florian
Der alte Mann und das Hub
Wohnort: Frankfurt am Meer
ForumBadges: Bild
Beiträge: 25876
Registriert: 23.09.2003 12:25

Ego Regulator

#1

11.01.2005 10:22

Originally posted by R3MY
As promised, here it is. This information can alson be found in the manual.

Supplies:

Lube (dow-33, vaseline, slickhoney, etc.)
Gun-Oil (gold cup, PMI, etc.)
Allen Wrenches (3/32nd)
Needle Nose Pliers
Towel/Rag/T-shirt
Q-Tips

Step-One: Disassembly
Remove the reg. from the EGO asa. Remove your macroline or steel braided hose from its connection.

Bild


Remove the bottom of the regulator by turning it counter clockwise (this may take some time, I had to use a strap wrench and a towel).

Bild

Make sure you hold the reg. upside down and remove the bottom half of the reg. Inside the top half is the piston and washer stack. To remove the plunger take the needle nose plyers, grab the top of the plunger and simply pull it out (you can also take an allen wrench or sumthen and push it out through the top). Now insert the 3/32nd allen wrench into the bottom of the regular and screw clockwise (inward). Keep screwing until you don't see the screw making any more progress. Then push up on the allen wrench and the screw will pop out.

Bild

Step-Two:Lubrication
Use the Q-Tips to wipe away any dirt, oil, or paint that might be inside the top half of the regulator.

Now take the piston and wipe away any dirt, oil, paint whatever may have collected on it. Take a little bit of the lube (i used dow-33) and rub a light layer onto the o-ring.

Bild


Now take the screw from the bottom of the regular out. Use the Q-Tips to wipe away any dirt, oil, or paint that might have collected in the bottom of the regulator. Now wipe away any oil, dirt, or paint that may be on the top of the piston. Take the gun-oil and put a couple drop on each o-ring and lighlty rub it in.

Bild

Step-Three: Reassembly
Take the piston and washer stack and place them back into the top part of the reg. (the disk on the bottom goes in first, washers go in last).

Now take the screw and push it back into the top of the bottom part of the reg. Screw counter-clockwise untill the screw will not turn any more (this is tricky. you have to take an allen wrench and put it on the top part of the bottom of the reg. and push it against sumthen like the wall or the floor. while ur pushing it in screw the screw counter-clockwise about 1 1/12 turn and it should catch the threads). Once the screw will not turn anymore screw it in 2-3 turns and that should put the reg at about 300-350 psi.

Now take the bottom half and top half and screw them back together. Then simply screw it back into the EGO asa and connect your macroline or steel-braided hose.

Bild

von pbnation

Link:
BBcode:
HTML:
Hide post links
Show post links
futji
X-Baller
X-Baller
Beiträge: 3095
Registriert: 09.09.2005 17:02

#2

08.08.2006 15:49

das piston in Bild 3 ist falschrum

muß so wie im Bild aussehen
Dateianhänge
image_281230.jpg
image_281230.jpg (21.92 KiB) 2334 mal betrachtet
Zuletzt geändert von futji am 08.08.2006 16:00, insgesamt 2-mal geändert.

Link:
BBcode:
HTML:
Hide post links
Show post links
Benutzeravatar
RST
Tekkenman
Wohnort: FFM Airport
ForumBadges: Bild
XtraBadges:
zeigen
Beiträge: 2863
Registriert: 10.03.2003 15:35

#3

08.08.2006 15:52

Krass, fällt erst nach über anderthalb Jahren auf :doh:

Link:
BBcode:
HTML:
Hide post links
Show post links
futji
X-Baller
X-Baller
Beiträge: 3095
Registriert: 09.09.2005 17:02

#4

08.08.2006 15:54

besser wie nie :wink:
hat warscheinlich keiner so wirklich drauf geachtet

Link:
BBcode:
HTML:
Hide post links
Show post links
moedy
Rookie
Rookie
Beiträge: 591
Registriert: 25.10.2006 20:45

#5

17.02.2007 00:02

deshalb fallen einem auch die 'teller' meistens gleich entgegen.. grrrr
von diesen scheibchen auf dem piston ein close-up waere von vorteil.

Link:
BBcode:
HTML:
Hide post links
Show post links
Benutzeravatar
Sh4d0w
X-Baller
X-Baller
Wohnort: Wien
Beiträge: 2935
Registriert: 10.12.2003 13:30

#6

17.02.2007 04:07

)()()()()()()()( wenn die scheibe die so entgegenschaut -----|

sorry 4 uhr und besoffen

Link:
BBcode:
HTML:
Hide post links
Show post links

Zurück zu „Planet Eclipse“

Wer ist online?

Mitglieder in diesem Forum: 0 Mitglieder und 6 Gäste